How To Thin Gel Coat

via

What can I use to thin gelcoat?

Gelcoat may be thinned for use in a Portable Preval Sprayer with styrene monomer. You can spray it with a polyvinyl alcohol (PVA) before gelcoat reaches its gel stage (5-10 min.), or adding 1oz per quart of a wax additive sanding aid. via

Can you thin out gel coat?

Thinning gelcoat should only be done when it needs to be, such as for spray applications. For most applications, gelcoat should only be thinned with styrene (which creates the very recognizable smell that gelcoat and polyester resin emit). There are also specialty thinning products designed for gelcoat application. via

Can you use acetone on gel coat?

Gelcoat stains may be localized or cover the entire topsides and hull. When removing a stain, the objective is to eliminate the stain without damaging the gelcoat itself. Avoid using strong solvents, such as MEK or acetone, and abrasives such as heavy rubbing compound or, worse, sandpaper. via

Can you use xylene to thin gelcoat?

It will clean the white vinyl without really attacking and dissolving it like acetone or lacquer thinner will. I`ve always found that Xylene will do the same job that laquer thinner will do, except it doesn`t evaporate as fast, so less is needed. via

Can you gelcoat over fiberglass?

Nope! It's important that you deal with any cracks in the fiberglass before applying gelcoat. You need to have a smooth fiberglass surface before you apply gelcoat. via

How do you spray gelcoat? (video)

How long do you wait between coats of gelcoat?

Apply gel coat to your part. Spraying gel coat is recommended for more accurate and consistent coverage. Apply gel coat in 4-5 layers at approximately 5 mils each, allowing 15-20 minutes between layers for a total thickness of 20-25 mils. via

How much can I thin gel coat?

It is possible to add more if you wanted to thin the resin down for any particular reason - generally you can add up to around 3 - 7% before you start to effect the properties of the resin. For instance you can convert a brush gelcoat to one thin enough to spray by adding styrene. via

Can you spray Flowcoat?

Crystic® Flowcoat GT-900 has been approved by Lloyd's Register of Shipping. We can now supply Spray Gelcoat in ANY colour, including colour matching to your sample - please call us on 0191 4975134 for colours not listed below. via

Does mineral spirits hurt gelcoat?

Can Mineral Spirits harm the gelcoat? No, but it will remove wax. via

Is acetone bad for fiberglass?

Abrasive products will scratch, discolor and dull the fiberglass surface. Fiberglass surfaces, like other surfaces, are susceptible to stains. Acetone removes not only dirt and grime from your fiberglass surfaces, but also any set-in stains like rust and pen marks. via

Will paint remover damage gelcoat?

This stuff works well, but don't use most paint strippers. They're too aggressive, and will damage the gelcoat. via

Can you thin Flowcoat with acetone?

It is possible to use acetone to thin gel coat, but there is a chance the gel coat will be rubbery or soft. Styrene, on the other hand will promote cross-linking of the resin and catalyst. Do not add more than 10% styrene or acetone by volume. Thinning the gel coat gives it a better flow when spraying. via

Does lacquer thinner damage fiberglass?

Acetone and paint thinner should only be used for stains such as oil or paint. Since these materials can harm the fiberglass, only use them to tackle especially bad stains. Spot clean using acetone and paint thinner, so you don't damage any areas not heavily stained. via

Can you use xylene on fiberglass?

Fiberglass is typically finished with acrylic, which can be dissolved with xylene. The biggest risk is probably color loss at the application site. via

Leave a Comment

Your email address will not be published. Required fields are marked *