How To Nail Hardie Board

via

What kind of nails do you use on Hardie board?

James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates. Min. via

How do you nail Hardie panels? (video)

How do you fasten Hardie board?

Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom. via

Can I use a framing nailer for Hardie siding?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. You may also find that siding nailers are a few pounds lighter than framing guns. via

Can you put screws in Hardie board?

James Hardie Building Products recommends keeping nails or screws at least 3/8 inch from the end of a plank. Drill pilot holes, at each mark, one-quarter to one-half inch deep, to make it easier to insert screws and prevent cracking the siding. Align the bracket holes with the pilot holes in the siding. via

Do you need special nails for Hardie siding?

NAIL TYPE:

Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails. via

How much does it cost to install Hardie panel?

Hardie Board siding materials cost $3 to $6 per square foot, and the labor cost to install is $3 to $7 per square foot. Old siding removal adds $0.25 to $1 per square foot when residing. via

Is Hardie panel waterproof?

No water penetration through HardieBacker® Cement Board with HydroDefense™ Technology during 48-hour hydrostatic test. HardieBacker® Cement Board with HydroDefense™ Technology is a long-lasting, waterproof solution for walls, floors, and countertops. via

How do you install Hardie board over existing siding? (video)

Can you use a nail gun on Hardie board?

Nailing Basics

Fiberboard cement siding can be hand-nailed, but because it's so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Don't drive nails into the siding at an angle. via

Do you need plywood behind Hardie board?

Fiber cement siding should be installed over plywood, OSB, or sheathing. Be sure that the siding installed is dry. Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches. via

Can you use a brad nailer for cement board?

2 3/8" ring shank nails for the framing gun should work just fine. Set the air pressure and nail depth adjustment on the nail gun so that it does not sink the nail head past the face of the siding. If the nail does not fully set give it a tap with the hammer, that is better than setting them to deep. via

What degree framing nailer is best?

30-Degree Framing Nailers

These framing nail guns come angled from 30- to 34-degrees. The angle of the degree being the greatest, they provide the greatest access to tight angles in framing applications. via

What is the best nail gun for siding?

Best Siding Nailer Reviews

  • BOSTITCH Coil Siding Nailer.
  • Freeman Pneumatic Siding Nailer.
  • Metabo HPT Coil Siding Nailer.
  • MAX CN565S3 Siding Coil Nailer.
  • HBT 15 Degree Coil Siding Nailer.
  • Hitachi Coil Siding Nailer.
  • DEWALT DW66C-1 Fencing Nailer.
  • via

    Leave a Comment

    Your email address will not be published. Required fields are marked *